Honeywell Marine Radio MX7 Tecton User Manual

MX7 Tecton™  
Hand-Held Computer  
®
With Microsoft Windows Embedded CE 6 or  
®
Windows Mobile 6.5 Operating System  
Quick Start Guide  
TECTON-QS Rev A  
4/12  
 
Bluetooth and MX7 Tecton  
Please refer to the MX7 Tecton Reference Guide for  
information when using the MX7 Tecton with Bluetooth.  
ActiveSync  
Installing ActiveSync on Desktop/Laptop  
ActiveSync (version 4.5 or higher for Windows XP  
desktop/laptop computers) must be resident on the  
host (desktop/laptop) computer. Windows Mobile  
Device Center is required for a Windows  
Vista/Windows 7 desktop/laptop computer. ActiveSync  
and Windows Mobile Device Center for the PC are  
available from the Microsoft website. Follow Microsoft's  
instructions to locate, download and install ActiveSync  
or Windows Mobile Device Center on your  
desktop/laptop.  
 
ActiveSync using USB-Client Connection  
The only connection type is USB Client.  
1. Connect the MX7 Tecton end of the USB cable  
to the I/O port on the bottom of the MX7 Tecton.  
2. Connect the USB type A connector on the I/O  
cable to a USB port on a PC or laptop.  
ActiveSync starts automatically when the USB cable is  
connected.  
When the MX7 Tecton loses connection (e.g., enters  
Suspend Mode), the connection to ActiveSync will be  
temporarily lost. When the MX7 Tecton resumes, the  
ActiveSync session will automatically re-connect.  
Please refer to the MX7 Tecton Reference Guide for  
ActiveSync information.  
 
Setting Up the Radio  
If the access point uses an authentication protocol  
(WEP, LEAP, etc.), your radio must use the same  
authentication. Please contact your IT department for  
WEP keys or LEAP credentials. Please refer to the  
MX7 Tecton Reference Guide for information on using  
WPA.  
1. Tap Start > Programs > Summit > SCU OR  
tap the Summit Client Utility icon on the  
desktop.  
2. Tap the Admin Login button and enter the  
password (default = SUMMIT).  
3. Tap the Profile tab and make sure the Default  
profile is selected.  
4. Select SSID and enter your SSID value.  
5. If the access point is using WEP, select WEP  
from the Encryption pull down list.  
6. Tap the WEP keys/PSKs button and enter the  
WEP Key(s) and tap OK. Skip to step 12.  
7. If the access point is using LEAP, select LEAP  
from the EAP Type pull down list.  
8. Select WEP EAP from the Encryption pull down  
list.  
9. If the Cisco/CCS certified AP is configured for  
open authentication, set the Auth Type radio  
parameter to Open.  
10. If the AP is configured for network EAP only, set  
the Auth Type radio parameter to LEAP.  
 
11. Tap the Credentials button and enter the User  
Name and Password.  
12. Tap the Commit button to save the radio  
configuration.  
13. Tap the Main tab. Wait for a radio connected  
message.  
14. Tap the Admin Logout button when finished.  
15. Reboot the MX7 Tecton.  
Please refer to the Radio Mode parameter in the MX7  
Tecton Reference Guide. It is important that this  
parameter setting corresponds to the Access Point to  
which the MX7 Tecton connects.  
 
Setting Up AppLock  
MX7 Tecton devices are shipped to boot in  
Administration mode. In this mode, the user has full  
access to the device and no password is needed. After  
the administrator completes the process below, the  
MX7 Tecton switches to end-user mode and restricts  
access to only the specified application(s).  
1. Tap Start > Settings > Control Panel >  
Administration icon.  
2. Assign application(s) on the Application tab  
screen.  
3. Assign a password on the Security tab screen.  
4. Select a view level on the Status tab screen, if  
desired.  
5. Tap OK.  
6. Press the hotkey (Ctrl + Shift + A) sequence to  
launch AppLock and lock the configured  
application(s).  
7. The device is now in end-user mode.  
 
Connecting Using RFTerm  
Before you make a host connection, you will, at a  
minimum, need to know:  
l
the alias name or IP address (Host Address)  
and  
l
the port number (Telnet Port) of the host system  
to properly set up your host session.  
1. Make sure the mobile client network settings  
are properly configured. If you are connecting  
via WLAN (802.11x), make sure your MX7  
Tecton is connected to the network.  
2. Launch RFTerm by tapping the RFTerm icon  
on the desktop.  
3. Select Session > Configure from the  
application menu and select the host type. This  
is dependent on the host system to which you  
are connecting; i.e., 3270 mainframe, AS/400  
5250 server or VT host.  
4. Enter the Host Address of the system. This  
may either be a DNS name or an IP address of  
the host system.  
5. Update the telnet port number if your host  
application is configured to listen on a specific  
port. If not, use the default telnet port.  
6. Select OK.  
7. Select Session > Connect from the application  
menu or tap the Connect button on the Tool  
Bar.  
 
8. Upon a successful connection, the host  
application screen is displayed.  
To change options (e.g., Display, Colors, Cursor,  
Barcode), please refer to the RFTerm Reference Guide  
for descriptions of these and other features.  
 
Rebooting the MX7 Tecton  
To warmboot the MX7 Tecton with Windows CE 6.0:  
1. Select Start > Settings > Control Panel >  
Registry.  
2. Tap the Warmboot button.  
To warmboot the MX7 Tecton with Windows Mobile  
6.5:  
1. Using the Registry, select Start > Settings >  
Control Panel > Registry.  
2. Tap the Warmboot button.  
When the MX7 Tecton is booting, there may be small  
delays while the wireless client connects, applications  
launch, remote management completes and Bluetooth  
devices connect.  
 
Disclaimer  
Honeywell International Inc. (“HII”) reserves the right to make  
changes in specifications and other information contained in this  
document without prior notice, and the reader should in all cases  
consult HII to determine whether any such changes have been  
made. The information in this publication does not represent a  
commitment on the part of HII.  
HII shall not be liable for technical or editorial errors or omissions  
contained herein; nor for incidental or consequential damages  
resulting from the furnishing, performance, or use of this  
material.  
This document contains proprietary information that is protected  
by copyright. All rights are reserved.  
© 2011-2012 Honeywell International Inc. All rights reserved.  
Other product names or marks mentioned in this document may  
be trademarks or registered trademarks of other companies and  
are the property of their respective owners.  
 
Patents  
For patent information, please refer to  
Technical Assistance  
Contact information for technical support, product  
service, and repair can be found at  
Limited Warranty  
information for your product’s warranty information.  
User Documentation  
To download the MX7 Tecton user documentation go  
 

Graco Baby Swing 1760908
Graco Stroller PD245623B User Manual
Hotpoint Cooktop EW71 User Manual
HP Hewlett Packard Calculator 17bII User Manual
HP Hewlett Packard Home Theater Server KPEC992M User Manual
HP Hewlett Packard Laptop 4311S User Manual
HP Hewlett Packard Weather Radio HP 85031B User Manual
Husky Vacuum Cleaner HV02000 User Manual
Iiyama Computer Monitor MA203DT D User Manual
Image Treadmill IMTL715040 User Manual